Today we have another re-post from our departed friend. Kevin O’Brien, AKA “Hognose” owner and writer of weaponsman.com.
There’s a bunch of little news bits going around the Army about maintenance issues and problems. We’ll cover them from most to least serious:
Item: Somebody Blew It
File photo of failed M9 slide. Not the mishap firearm.
In late 2015, a very high (but unknown) round count M9 pistol had a catastrophic failure of the slide. With the Army scrimping on O&M money, especially on the ripe-for-replacement Beretta handgun, failures are not unusual and usually turn out to be fatigue failures from parts that have been carelessly used long past their service life. So was this one. The pistol was older than the soldier shooting it, and, as it turned out, someone, somewhere had pencil-whipped the maintenance records.
Slides fail every week, somewhere in an Army with hundreds of thousands of pistols that were almost all bought 30 years ago. But what happened next wasn’t supposed to happen. When the pistol slide failed at the slide’s weakest point, the locking-block cuts, the rear half of the slide kept on motoring, striking the GI in the cheek and upper jaw area and causing non-life-threatening injuries.
The investigation determined that a mandatory maintenance work order, MWO 9-1005-317–30-10-1, issued twenty-seven years ago in March, 1989, had never been complied with. They couldn’t track where the pistol was at the time it was not repaired; Army units and activities with M9s had until June, 1993 to comply.
Somebody reported that his M9s were in compliance, when they weren’t. This is what you get when a zero-defects, up-or-out culture undermines integrity while at the same time penny-pinching undermines maintenance. The soldier who drew that defective M9, and every soldier that’s been drawing and shooting it since 1989, is damned lucky to be alive. (Fortunately, when a slide fails on most pistols (or a bolt on a Mauser C96, etc.), gravity usually ensures that the part hits below the eye, on cheek, jaw, chest or shoulder).
Meanwhile, the Army sent an urgent Safety-of-Use message mandating an Army-wide inspection of all M9s for completion of the MWO. Since the resources for completing the MWO no longer exist, the remedial action is to immediately deadline and turn in the offending M9 and draw a replacement.
How many units pencil-whipped their response to that ALARACT message?
Item: Safety? Sometimes it’s Evolution in Action
Word is, some genius removed himself from the breeding population of Homo sapiens in 2014 by “improvising” M203 ammo (may have been 320) by cutting the links off of (higher-pressure) Mk19 belted ammo. The links were actually designed so they couldn’t snap off by hand, to prevent that.
Can we get a “FOOM!” from the assembled multitudes?
And oh, yeah, trying to belt up 203 ammo and fire it in an Mk 19 leads to FOOM also, of a different variety — out of battery ignition. Another opportunity for poka-yoke missed.
Item: Ambi Selectors Reaching Troops.. slowly
The Army has finally woken up to two facts:
- About 10% of the troops are left-handed, and
- There are lots of good ambi selectors available.
So the Army chose one and put it into the pipeline. So far so good, right? Not entirely. The selectors are only being replaced when the weapons are overhauled. And they don’t fit in the M12 racks many units still have. Work around is to cut a notch in the rack with a torch, or with a file and plenty of time, or to bend the part of the rack that hits the right-side selector out of shape so that the selector clears the rack.
Also, the slow migration of the ambi selectors means not all M4/M16 weapons in any given unit have them. Why don’t they just push the parts down to the unit armorers? Three reasons:
- The big one: they’re afraid of armorers stealing parts if they take rifles apart
- It doesn’t fit the concept of echeloned maintenance, even though that’s being streamlined;
- They don’t trust the armorers let alone the Joes, not to botch the installation.
On top of that, of course, it’s not penny wise and pound foolish in the great Army tradition.
Item: New Stuff Coming in, Old Stuff Going Out
A number of new arms are reaching the troops, and old arms are going away. We’ll have more about that in the future, especially the M2A1 and the coming “rationalization” of an explosion of shotguns and sniper rifles. We just broke it out of this post to keep the length manageable.
ITEM: MG Maintenance Problems = Operator Headspace & Timing
The biggest single problem the Army has with the current pair of machine guns (M240 and M249) is burned out barrels. That’s caused by not changing barrels, either in combat, or especially on the range. Often, units go out without the spare barrel so it’s not like they gave themselves any option. (The M2 version of this is going out with only one set of gages for the M2s. The gages are not required for the M2A1). The Army is falling back into the peacetime mindset of “leave it in the arms room and we can’t lose it.” True enough, we’ll just destroy the one we take out instead.
The fact is, and it’s a fact widely unknown to GIs, MGs have rate-of-sustained-fire limitations that are lower than they think. (Remember the MGs that failed at Wanat? They were being operated well outside their designed, tested envelope).
The M249 should never be fired more than 200 rounds rapid fire from a cold barrel. Then, change to a cold barrel, repeat. The Army being the Army, there are geniuses who think that they can burn a couple belts in a few seconds, change barrels, burn a couple belts in a couple more seconds, then put the original honkin’ hot barrel back in and burn — you get the idea. If you have a situation where you’re going to fire a lot of rounds from a single position, like a predeployment MG familiarization for support troops or a defensive position, you might want to lay in some extra barrels (and yes, Army supply makes that all but impossible, so you have to cannibalize your other MGs).
The M240 is a little more tolerant but should still be changed every 2 to 10 minutes of firing, and even more frequently if the firing tends towards real sustained fire. (The deets are in the FM, which is mostly only available on .pdf these days).
One last thought, your defensive MG positions need to have alternate, displace positions, and you need to displace after sustained fire from one position — unless you want to share your hole with an exploding RPG, ATGM or mortar round. “Where’s your secondary position?” or “-fallback position?” should not produce the Polish Salute.
As ordnance experts have observed ever since World War II, a barrel can be burnt out due to overheat and still mic and even air-gauge good. You only know it’s hosed when it can’t shoot straight.
Well-maintained MGs are more accurate than people seem to give them credit for. Some SOF elements have selective fire M240s and really, really like them. (The standard M240 has no semi setting). They’re capable of surprising accuracy from the tripod.
ITEM: For Want of a Cord, a Career was Lost
GIs frequently lose or throw away the idiot cord on the PVS-14 night vision monocular. If these sights were being properly inspected, which they usually aren’t until a team comes in just before deployment, they’d be tagged NMC (non mission capable) for missing that stupid cord. You don’t want to be in the bursting radius of a unit CO who’s just been told 85% of his night vision is NMC… especially when that news is delivered in earshot of his rater and senior rater. It’s a bull$#!+ requirement but it’s in the book, and if the Army ever has to choose between following the book or winning the war, the book comes up trumps every time.
You’re not going to stop GIs from losing cords, but replacement cords are in the supply catalog